라즈베리 파이를 이용한 개인 노트북이네요...
Aw, yes, the Raspberry Pi Computer, a credit card size mini PC that only cost $35. There are so many possibilities and uses for these small nano PCs. People have made them into PVRs (personal video recorders), retro gaming machines, weather stations, in-car PCs, jukeboxes, and so many more creative ideas. When I started this project four weeks ago, I just wanted to see if it was possible to make an ultra portable, mobile Raspberry Pi that you can take to-go. As I was building my Pi-to-Go I kept saying to myself, it would be cool if it had this, and then I would find a way to make it happen.
My mobile Raspberry Pi Computer is now complete and because this is an open source project I wanted to show you everything, including how to build one yourself. I will even provide links to the parts I needed to purchase and the 3D printer STL files to print your own case. So here we go!
Just a quick blurb about myself. I am the founder and CEO of Parts-People.com, Inc. which specializes exclusively in Dell Laptops; and specifically Dell replacement parts, Dell laptop repair, and Dell laptop refurbishing. So I have more than 10 years experience in repairing and building laptops. Okay, lets move on.
LCD Screen
The LCD I used is from an after market backup camera system that can be installed in a car. The screen is a low resolution and I hope to find a better upgrade for my next version of the mobile RPi to-go. So for this proof of concept, it works just fine. The screen is 3.5″ using a 4:3 aspect ratio. It uses a composite input and is able to display a resolution of 640 x 480 pixels.
Battery Pack
First off, be very careful when messing with lithium-ion batteries. Neither Parts-People.com, Inc nor I are responsible for any damages caused by this tutorial. Proceed at your own risk. Because I own a company that sells only laptop parts, it is only natural that I would use a laptop battery for this build. Laptop batteries are built in such a way that you cannot just plug something into them and use them for a battery pack. I knew it would be possible but I just needed to figure out the best way to get power out of it and how to charge it back up in the best and safest manner. I ended up using a battery for a Dell Latitude D600 laptop and just removed it from the Dell battery case. The battery was about the right size, it had the right voltage, and I had plenty of them. Those batteries have a standard Dell 9 pin battery connector. To get power out of this battery, you will need to connect pins 1,2, & 4 together for negative / ground (-) and pins 8 & 9 together for positive (+). Be sure to connect the correct leads. See picture for pin outs.
Charging the battery was easy, I just purchased an after market laptop battery charger. It connects directly to the battery’s 9 pin connector and also has a battery level indicator built-in.
Internal Powered Hub
One major problem with the Raspberry Pi is a lack of power. The RPi is powered by a micro USB 5v with at least 750ma, 1A is better. But the problem is not there, it is that the USB port can only supply in the neighborhood of 120ma per port, which is not enough to run much. So I found a super small 7 port USB hub that is powered and took it apart. I needed to power 5 things: a wireless WiFi dongle, a bluetooth dongle, an SSD hard drive, a keyboard/mouse transmitter, and the Raspberry Pi itself. The power from the battery pack is 11.1 volts and the power required for the USB hub was 5 volts. What I did was connect the battery to the LCD screen which had an input of 9v-13v, and I knew that the LCD screen would have some components that would require a 5v power source (LED LCD back light for example). All I had to do was find the onboard voltage regulator and solder on leads across the 5v capacitor and solder those to the 5v input on the powered USB hub. Easy as Pi. Now we have clean regulated power for all of our devices.
Extended Storage
64GB SSD, yes I did! I wanted to add a linux swap partition because of the lack of RAM. The Raspberry Pi itself has 256MB (model B version 1) or 512MB (model B version 2). If I simply just installed a larger SD card and added a large swap file, or swap partition, I would eventually burn out the SD card. SD cards have a very limited number of read/writes and SD cards are slow. I opted for a 64GB Sata II solid state hard drive made by Samsung (model # MMBRE64GHDXP) and again I have a bunch of those in stock so it was convenient. I used an external USB hard drive caddy’s circuit board to connect the SSD sata HDD directly to the internal power USB hub. I setup a 1GB (1,024 MB) Linux swap partition, and have the rest formatted in ext4 for extended storage.
Built-in WiFi & Bluetooth
I wanted to build in as many features as possible, so I got a nano USB WiFi dongle and a nano USB bluetooth dongle to install inside the mobile Pi. These are also soldered directly to the built-in powered USB hub.
Operating System
I’m using stock Raspbian Linux downloaded from raspberrypi.org. The only tweaks I made were to the config.txt file and added the Linux 1GB swap partition. I modified the config.txt file to make the LCD screen display properly and fill the whole screen.
config.txt changes
overscan_left=8
overscan_right=-40
overscan_top=-30
overscan_bottom=-30
sdtv_mode=2
Keyboard & Touchpad Mouse
I purchased a wireless 2.4Ghz USB keyboard & mouse combo. I would have preferred a wired USB but this one was the right size and price. The keyboard slides in and out via the access door on the left side of the machine. The access door also exposes the on/off switch and mini USB charge port for the keyboard too.
Overall Specs
The Raspberry Pi board I am using is a model B (revision 1) but you can use the model B (version 2) for this build.
| CPU | Broadcom BCM2835 ARM11 700Mhz |
| Memory | 256MB (shared with GPU) |
| Main Storage | 4GB SD Card (OS Installed) |
| Extended Storage | 64GB Sata II SSD (1GB linux swap) |
| WiFi Wireless | Built-in B/G/N Card |
| Bluetooth | Built-in Bluetooth 3.0 |
| Peripherals | 1 Powered USB Port |
| Video Output | HDMI Port |
| Keyboard / Mouse | QWERTY Keyboard with Touchpad Mouse |
| Weight | 1.65 lbs. |
3D Printed Case
Using Google sketchup, my 3D printer, and a little creativity I was able to create a case for this mobile Pi to-go. There are five parts to the case and I have made all five parts available for download from thingiverse.com.
Download Pi-to-Go 3D files (STL) Here
Everything is made to snap together except the back access door is held on by four screws. The back of the case has a Raspberry Pi logo cut into it and it is illuminated when the device is powered on. I used a back lighting LED and the acrylic strip from the back of a backlit laptop keyboard. I cut it to the shape to fit just behind the RPi logo and soldered leads that connect to 5v power. This was not needed but I thought it was a nice touch.
Where to buy the parts
As promised I will provide links to purchase all parts needed and I have already provided the links to download the 3D printer files (STL) above.
- LCD Screen – bought on amazon for $17.95 – here
- Raspberry Pi – bought on Newark/Element14 for $35 – here
- Mini Keyboard/Mouse – bought on amazon for $29.95 – here
- Standalone Battery Charger- bought on amazon for $75.00 – here
- Powered 7 Port USB Hub – bought on Parts-People.com for $14.95 – here
- 64GB SSD Hard Drive – bought on Parts-People.com for $69.95 – here
- Dell D600 Battery – bought on Parts-People.com for $88.50 – here
Schematic
Here is a schematic to show how everything is wired together.
More Pictures
'하드웨어 설계 > 라즈베리파이 및 아두이노' 카테고리의 다른 글
| 아두이노 – 나도 해보는 LED 깜빡이기 (0) | 2016.01.31 |
|---|---|
| 라즈베리파이 - 2*16 LCD 에 Hello World 띄워보자 (16) | 2014.06.03 |
| 라즈베리파이 LED 테스트 c언어 이용 (펌) (0) | 2014.05.30 |
| 라즈베리파이 GPIO 핀배치도 (펌) (0) | 2014.05.30 |
| 라즈베리파이 - 고정 ip를 이용해서 원격 접속하기 (0) | 2014.01.28 |